Technical Specifications Supported Signal Types: 4‑20 mA current‑loop, 0‑10 VDC voltage analog signals Channel Configuration: 16‑point analog termination capacity Field Termination: Screw‑clamp terminal blocks Back‑Side Interface: Dedicated multi‑pin connector for Triconex analog cable assemblies Field‑to‑logic Isolation Voltage: 1500 V RMS Installation Method: DIN‑rail mounting inside control cabinet Operating Temperature: -20 °C to +60 °C Storage Temperature: -40 °C to +85 °C Relative Humidity: 5%‑95%, non‑condensing Certifications: SIL3, IEC 61508, UL, CE Hardware Revision: REVA Weight: 1.36 kg
Functional Features Multi‑signal‑type analog termination supporting both current‑loop and voltage‑mode field instruments. Screw‑clamp field terminals accept multiple‑gauge industrial instrument conductors. Rear‑side dedicated multi‑pin connector for connection with original Triconex analog cable assemblies. Internal passive noise‑suppression circuit improves analog signal stability in noisy cabinet environments. Hardware revision REVA incorporates PCB layout optimization for reduced signal crosstalk. Hot‑swap maintenance support, field instrument wiring remains connected during I/O module replacement. Integrated multi‑point grounding interface for field‑cable shield termination. Full compatibility with loop‑diagnosis functions of matched Tricon analog I/O modules.
Application Scenarios Mixed‑signal analog‑loop termination for petrochemical SIS safety instrumented‑system. 4‑20 mA transmitter and voltage‑sensor signal transition for oil‑gas safety‑control cabinets. Refinery safety‑monitoring analog‑signal field‑wiring marshaling. Chemical‑plant reactor safety‑related analog‑instrument termination. Power‑plant safety‑interlock mixed analog‑signal cabinet‑internal transition. SIL3‑rated process safety‑system analog‑loop wiring interface.
Performance Parameters Additional Loop Resistance: Minimal extra resistance impact for 4‑20 mA current‑loop circuits Inter‑Channel Crosstalk: Optimized REVA PCB layout reduces adjacent‑channel analog crosstalk Contact Reliability: Stable low‑resistance contact performance under long‑term cabinet vibration Signal Accuracy Impact: Signal deviation stays within 0.1% full‑scale range Shield Compatibility: Supports individually shielded twisted‑pair field instrument cables
Material Composition Main circuit substrate: REVA‑revision conformal‑coated low‑noise analog printed circuit board. Assembly housing: Flame‑retardant reinforced industrial engineering plastic. Termination components: Alloy screw‑clamp terminal blocks. Back‑side connector assembly: Gold‑plated multi‑pin industrial locking connector. Internal components: Passive noise‑suppression electronic components. Mounting hardware: DIN‑rail spring locking clip and anti‑loosening metal screws.
Structural Characteristics DIN‑rail‑mount modular termination assembly structure. Front‑panel exposed screw‑clamp terminals for convenient field‑instrument wiring access. Rear‑mounted multi‑pin locking connector for analog cable‑assembly connection. Multiple dedicated grounding points for field‑cable shield centralized termination. Revision marking REVA printed on assembly housing surface. Spring‑loaded locking clip secures assembly firmly onto standard DIN rail.
Working Principle Analog signals from field instruments connect onto front‑panel screw‑clamp terminals of 3000656‑210‑REVA assembly. REVA‑revision PCB routes each analog signal to rear‑side multi‑pin connector. Signals transmit through original analog cable assembly to matched Tricon analog I/O module. Built‑in passive noise‑suppression components restrain high‑frequency electromagnetic noise coupled onto signal lines. Field‑cable shields terminate to assembly grounding points and divert interference‑noise energy to cabinet protective earth bus. Bidirectional signal path enables Tricon I/O module to execute field‑loop open‑circuit and short‑circuit fault diagnosis.
Installation Requirements Mount termination assembly onto standard 35 mm DIN rail inside sealed industrial control cabinet. Connect cabinet protective‑earth bus to assembly dedicated grounding terminals. Field instruments shall deploy shielded twisted‑pair instrument cables. Use only original Triconex factory‑fabricated analog cable assembly for connection to analog I/O module. Tighten field‑terminal screws following manufacturer recommended torque specification. Separate analog signal wiring from high‑power power‑cable routing, maintain safe distance from frequency‑converter interference sources. Maintain cabinet ambient temperature and humidity within rated operating limits without condensation.
There are no reviews yet.